Do you want to hang your hammock?
Do you want to relax or take a break on a hammock?
Do you want your children to enjoy the hammock?
If you agree with the above question, then you require a Best Hammock Stand for yourself. The hammock stand will hang your hammock and will also make it swing. It is the perfect supporting system for your hammock and you can take a break and enjoy it. Given below are the 10 best portable hammock stand you can consider to but according to your requirements and budget that your pocket allows you:
Table of Contents
- Buying Guide for the Best Portable Hammock Stand in 2021
- FAQs on the Best Portable Hammock Stand for 2021
- What is the material used in your hammock stand?
- What is the hammock stand suitable for?
- How to clean your hammock stand?
- How to adjust the height of your hammock stand?
- How to DIY Foldable Hammock Stand?
- What is the standard weight capacity of your hammock stand?
- How to maintain the wooden or metal made hammock stand?
- What precautions should you take while using your hammock stand?
- Can your hammock stand damage the trees?
Buying Guide for the Best Portable Hammock Stand in 2021
Handle more weight:
Make sure that the hammock stand that you are planning to buy must be capable to handle enough weight for about two people with normal weight. Along with the good looks, your product must have good resistance against the elements and for that, it must be coated with the powder finish which will make your stand look good in appearance. According to the color of your hammock, you can choose either of the oil – rubbed bronze finish or the copper coating.
Easy to assemble:
It must not take much of your precious time in assembling your product and must be easy for you to do so. In addition to that, it must be 9 feet in size to give it an appropriate height. Moreover, it does not require any prior experience to assemble it and anyone can easily put the pasts of stand together in order without using any tools also. Also, it must be easy for you roll hook up your stand anywhere you want and for that, it must contain a double hoot set, a chain-hanging set, and a wheel kit.
Contains all accessories:
You must check your product that it contains various other accessories as well so that you do not have to worry about buying it separately. Buying the necessary accessories from outside can cause you to double than buying it along with the product only. It must contain a carry bag which is sturdy so that it can be used for transportation. Also, it must be available in different colors so that you have enough choice to buy from.
Sturdiness and rigidness must be provided by your hammock stand so that there is no stiffness and it must be long-lasting. With durable, you will be allowed to use your product for a long time. It must have six holes in it so that you can adjust it to your preferred height and these six holes must have space of about 4 inches between them. It must also ensure the safety of you and your family especially the children, so it must stand strong on the ground and should allow you to swing on it without falling on the ground.
Your hammock stand must be designed with steel which is high in quality and can easily withstand the various elements. To set it down smoothly on the ground, the end of the pole must be made up of steel which is sturdy and durable. Your stand must be so strong that it must resist the weather also and must be able to stand against the harsh weather. It must be suitable for the swinging and must include the need for any permanent element such as trees for the support.
Light in weight:
Buy your product which is not heavy but light in weight or else it could affect the load capacity of your hammock stand. If you are buying the hammock stand with the folded feature, then you will get a bag that will nicely pack the stand and must be light in weight for about 150 lbs. It must allow doing hiking and must also be resistant to rust when the stand is exposed to air or water and for that, it must be coated with rust-resistant powder.
Take little space:
Choose the product which is less in width so that it consumes less space of your building and must be less flat from the pole. With less space, it must also take less time of yours so that you can quickly put it up and down effortlessly. It must have the feature of folding so that you can carry it easily from place to place and must have saved a lot of your space. And when you are unfolding your product, its original size becomes 6’4” which is a perfect size for your home. It must not be flimsy and must have the ability to resist the rust and for that, you can apply the oil on it regularly if it is made up of the metal.
For about 450 lbs can be handle by your product to be proved as good incapacity. With a good capacity, it must handle the weight of two people at one time only without being collapsed and also must be simple in design. It must allow you to adjust it to the height according to your requirements. To keep your hammock stand safe, you must cover it in the winter so that it can withstand the harsh weather and must be made up of good material so that it can resist rust as well as other elements.
Your product must be available to you at an affordable price so that you do not have to spend so much of your money on it. You must buy it at a reasonable price and look for the hammock stand so that you can enjoy all the necessary features at a price that is allowed by your packet. To stabilize the stand, the end of the product must be coated with the plastic cups so that it can easily soften the tubing steel tubing. It must be wide enough for about as such 4 feet so that it can accommodate two people together easily.
Portable hammock stand for car camping
So this is my car portable hammock stand try it out last night and it seems to go well I’ve got a couple long lines there and then there’s a diagonal post to either end and the post is overall length about six feet three inches and then sitting on a little 2×4 and there is a piece of like 3/8 inch rebar that goes into the ground there that goes through that the 2×4 board and up into the it’s like one and a half by two and a half bore basically took a 2×4 and ripped it down the length to to make that that piece and then there is a dowel that is stuck in at the top it’s about two inches down which is just barely enough but time I wrap several different types of connections up there and here is the hammock it is about a 10 foot 6 inch long ridgeline overall hammock length is right at 12 feet laid flat on the ground and the tarp is a 12 foot by nine foot sill nylon tarp which I actually got from Walmart about the cheapest price and I needed to add all the little tie outs but did that.
Provided the basic tarp I had tried this set up with the posts initially standing vertical but I kept on sinking down to the ground basically I was just putting too much force onto the ropes which are 600 pound polyester rope ropes but I it I was sinking sinking sinking so I finally decided to angle the post in and that made.
All the difference in the world it stabilized and was firm worked well mmm it rained last night several different times and everything stayed dry I did have little drip lines on the hammock but it even though it was raining it there wasn’t enough coming in to really be dripping all that much I’m sure at some point there could be enough but I definitely did not get wet at all and it’s about noon noon time now and everything’s pretty well pretty well dry so I could take it down and put it away without needing to worry about it so that is my setup I think I’m going to take that to a camping trip coming up that I’m planning on taking by car oh also the length of that post that was the big design thing that was the longest length I could get in my little car with a seat folded down in the back and then there’s roughly about thirteen feet from connection point to connection point there with me thinking about having a it’s probably a little over that but I’ve got 12 foot tarp and I didn’t want to get any longer because I wanted my hammock to be up as high as I could get it and as it is I can I can clearly see it underneath the underneath the edge of the tarp I was thinking a little bit that I might you know benefit possibly in some weather from having a a wider tarp that would go down more or I could go down more steeply with it but I am the wind is kind of blowing in and I actually with me in it I I was.
Touching the tarp so I think on that side particularly I would want to leave it where it was anyway I did not get wet at all it wasn’t a tornado or anything so wind wasn’t blowing sideways but so I was fine so I I think it’s pretty good.
FAQs on the Best Portable Hammock Stand for 2021
What is the material used in your hammock stand?
The materials that you can usually find in your hammock stand is the bamboo, steel, and some other woods that are strong and sturdy so that it offers you the longevity. If you have the stand made up of woods then they are coated with the stains so that it can resist the moisture and can ultimately help you in making your product safe from the rust. The steel made stand are design in such a way that they can withstand any elements and can also stand strong when in the harsh weather, thus they are safe to use for the outdoor purpose as well as indoor.
What is the hammock stand suitable for?
The hammock stand is the best device for you and your family members to relax on and especially the children can enjoy it. Your product is suitable for the picnic, outdoor recreational activities, and many more you can do on it. It will give support to your back and you will feel comfortable on it while lying. You can either sunbathe under the sun or take a nap under the shade of a tree after reading a book, it will give you relaxation and will make you stress-free also. Furthermore, it gives you the option of using it either in woods or any place with height, so you can easily put it anywhere you like to relax.
How to clean your hammock stand?
To clean your hammock stand, you are required a mild detergent and water kept in a bathtub and after washing it, you need to dry it in the air. If your hammocks are made up of the fabric then you must clean it using the scrub brush, detergent, and mild water and use it only after it is completely dry. You must consider the instruction manual before taking another for the machine wash or else it will be damaged if it does not support the machine-washable feature.
How to adjust the height of your hammock stand?
You will be delighted to know that your hammock stand is capable of stretching naturally. In case, if you are not comfortable with its natural way of adjusting the height then you can tighten the end of the loop of your product with the help of the screwdriver and live the chain along with that. If your stand is old, then you have to increase the distance between the two poles as it will be difficult for you to adjust the chain of your hammock. If still, your preferred height is not getting adjust then it is an indication that it is time to buy a new one for yourself.
How to DIY Foldable Hammock Stand?
Today I’ll show you how I made this frame for nylon hammocks Hatteras hammocks.
It’s totally reconfigurable it folds down in all for around 55 dollars interested here we go the way I designed this is twist this off and you can go to a different hole it’s currently at 10 feet for this nylon hammock Hatteras hammocks they need about 15 feet so you can easily lower this down by going to say this hole right here and then you’re perfect or you can have this side down and this side up or vice versa.
Depending on what your situation is and how you like your hammock totally reconfigurable easy to work with made out of materials that you can pretty much get anywhere you can make a hammock frame like this for around fifty five dollars.
No kidding or less depending on what materials you already have on hand now comes illegal parts I cannot guarantee how anyone will make their own version of this I hope that you take this design and kind of incorporate the things that you like and maybe modify it for your purposes but I can’t guarantee the construction or the materials you’re gonna use so be safe out there this is just to give you an example and your builds are your responsibility this is a lot of fun it’s relatively easy to do I’ve kind of made some design elements incorporating almost like a Frank Lloyd Wright Hallie s Enosh kind of design with you know some Southwest influences what-have-you and it’s totally.
Functional you can actually cut this in half here with like an i-beam.
Construction I might do a follow-up video on that so you could actually get this to be all within four feet.
Footprint kind of all stuck actually you’d be five feet because that’s what this is here.
But it it’s easy to take apart you’ll see that later in the video so let’s get building this thing there’s a bunch of hammock frame videos out there I know that but what I’ll tell you the.
Difference in this one is I’m going to tell you exact dimensions on all the parts I’m going to show you all the critical construction and I’m going to give you design options to trade-offs based on the hammock that you’re trying to use let’s go over all the components this bill can be made with three 10-foot long two by fours and one eight foot long two-by-four it if you want to have a little extra margin you could get four ten foot long two by fours and make this project I’ll also list all the.
Components in the comment section below the video so you can check that out there I’m also gonna put all the.
Hardware components in there I’ll walk through the various hardware pieces hardware being the steel bolts and the nuts and things like that that need to go through to join this all together so let’s start with the bottom base the bottom base is two eight foot long two by fours this is an eight inch long piece and there’s two of those the bottom frame cross piece is right here there’s two of those they’re four foot long and then there’s these two square 2 by 4 blocks and I’ll show you in the video how to make those so that’s the bottom cross piece this is the angle support piece to the uprights the uprights are 110 foot long 2 by 4 cut in half so these are 5 foot long on either side these cross pieces are three foot long.
This here is 8 inches long and there’s another tourist finding piece up there 8 inches long I might change that to 12 we’ll see how that works out and that’s gonna be where you put your eyelets for suspending the hammock these pieces have already been put in place and they were screwed in with 4 inch long screws deck screws that were coated to make sure that in this case that the.
Pressure-treated wasn’t going to.
Interact with the metal screws here’s a hint when making these short square 4 by 4 pieces first thing I do is take a 2×4 and I just mark graciously because I want to make sure that it’s legitimate we just take a carpenter’s square these carpenter squares are great for this kind of thing get on the line and like I said I want to cut right on the line or left to the line and make sure that I have a square now trying to drill a hole into something that big is gonna be challenging so I’m actually gonna do a flip prep now when I come up here and I line up two corners and draw the center and measure twice cut once kind of thing take your time and get this hole right because it’s gonna be 3/8 inch they start out with a smaller drill to kind of blazed the trail with the hole and then I go in with 3/8 inch drill so I start with a quarter inch drill bit and then I graduate up to the 3/8 inch drill bit and I’m gonna do the hole before I do the cuts that’s the hole with the smaller drill bit and here’s that piece cut off of the end they’re nice and square and ready for the project this is the lower pivot point right here you can see I used similar X’s I did for these I used a 4 inch screw exterior put the coating on it and I screwed here and here I pre-drill using a drill bit about the size of the shaft but enough to get the grooves to grip onto so if you use a drill bit that’s about the size of this thickness here and you’re good to go that helps go through so I pre-drilled this ran it on this side on this side then on the other side it’s here in here so it’s a nice tight fit the next thing I’m gonna do is put on the legs or the supports going this way and I’m going to tie that in to this here right about there hi there.
Future Mike here earlier Mike didn’t know that he was going to replace this piece right here I said it was an 8 inch long 2×4 turns out that I’d rather use an 8 inch long 2 by 8 to give up a little stronger structure totally up to you the 2×4 would probably work but I really wanted to make this design as solid as possible so I’m using the square as a template clamped it down and I’m just pushing position I want to make sure that this is nice and flush it’s gonna meet up with this bottom I’ll show you that later.
And the whole idea of this drill bit going through here like this is to put a bolt in place so that these lakes can be taken off if you don’t want to do that you could just really simplify the build by taking the four-foot long cross piece and just drilling it into here like I’m gonna drill these two pieces here later on once I’ve marked the hole with the drill using this is the template then I just complete knowing all the way through into the two-by-four on the other side but you can kind of see here how you used the same technique on the other side and now I’m just between drill through straight I’m using an 8 inch bolt that’s the biggest one I could find if you could use an 8 and a half inch bolt you could probably put a nut on this end but since the threads aren’t going out that far I’m actually gonna put a tee nut on this end so this is going to be nice and solid.
Predrilled all the holes with a 964 inch drill bit again because it matches up well with the shaft of the screw I’ve got the screws already I’ve pre-drilled the holes into here and now it’s just a matter of screwing these in place over here to make the cross piece that’s what it looks like all screwed in and you can see it’s got a nice little pivot so if you have a little bit of a slope that’s fine if you didn’t want to have the ability to take this cross piece off you could permanently just screw it into these boards here again that’s totally a trade off for you I want to make it so I can disassemble it put in the garage and it doesn’t take up much space now just repeat everything I just did here on the other side since I put that cross piece on there I had to move to the workbench the workbench actually gets it off the ground it’s a lot easier a couple other hints here there’s the screws here’s the holes and I put d down for the down or the ones that you’re going to screw into and you might be tempted to screw in the wood on the side because it’s smoother and you want to screw into the cut side because then you’re going between the grains as opposed to against the grain here so it’s going to be a better connection and you won’t likely split the wood especially if you pre drill bit again you can totally forego the ability to take this off and simplify you won’t have to drill the bowl through you could actually screw into the wood here so I’ve got this yup right there and I’ve determined that the distance between this hole and this hole is I’m gonna do it in both centimetres and it’s.
Approximately 24 centimeters or nine and a half inches from the center of this hole to this hole this is the three foot long cross piece that goes on the bottom a couple things here first of all I’ve made this design if you’re gonna do like a Hatteras hammocks you probably need to come all the way out to the three feet because that will give you around 15 feet worth of distance but I’m only going to need it this far now.
I’ve done one side and that’s the most complicated things getting all these dimensions right you can see this red line here and some red lines here these are guides and this tells me that it’s on the left side is the red I’m going to use a blue marker for the right side so that I can tell these two pieces apart so if I disassemble it for some reason I’ll know which side is which and we’ll be able to keep it together you want to make sure you line these things up the way you drilled them originally so that’s the center hole here and I’ve just got a six inch 3/8 inch bolt all my hardware for this build is 3/8 inch the other thing these red lines are you can see this one’s at an angle this isn’t an angle this is straight this is to help guide me putting in the assemblies on the side over here on the red four left side you’ve got same marks on the two uprights and then this is at the base also so I know where to what angle to put so I can just put these bolts back in together you can put the bolt in here this end the bolt on this end and you’ve got a straight point and then you just use your 3/8 inch drill and drill straight down into this right here and that will give you an exact fit we’re looking at 20 inches on center here from the bottom hole that goes into the base and this that goes into the upright and metric folks out there 20 inches is about 51 centimeters this hole is drilled so now the blue piece will be the same as the red piece another hint since I’ve already done the red side what I did is I migrated the lines to the blue side so that would help speed up the process of putting that in place I’ve also marked X’s to identify the bottom piece in this case red X in the blue X I guess they could put B for bottom and then we’ll do the same thing so I’ll probably do that on this side go this is the base hole cross piece this line here is 1 foot from here.
Here you can see that it went around and I centered the holes so I could drill the same hole on both sides so I’ll take one of these uprights off for the other side when I make the other upright and drill those holes just as I did with the cross piece this is the upright on the other side and I’m going to use the one I’ve already cut as a template and then just drill through this hole and it’s all lined up you want to make sure that whatever when you line these two up originally for the five-foot piece and drilled this original hole you want to make sure that they’re lined up as flush as possible otherwise you’re gonna get a little goofiness at the top and when you try to put it in the end piece where you’re gonna suspend the hammock it’s not gonna work out this is a good for you a little bit of marking and.
Remembering really helps the build come along successful I’m using a 300-pound strength I bolt that’s a half-inch and you can see I’ve screwed it in them two sides here I might add a couple screws there.
You could also glue it got some screws here because the screws on this side are coming through the wood to about here so I’ll see if that’s enough screws the original piece here is eight inches I’m think I’m gonna go to the 12 inch I’m gonna bring this in a little deeper halfway point is right there and look at that so that’s where I’m gonna drill my hole gonna center punch it starting with a really small drill bit and build up to that half inch so we don’t crack the wood around here here’s the eye bolt I’m using it’s a 1/2 inch 6 inch long and you can see it’s good for 300 pounds here is the eye bolt in the 2×4 you can see that I’ve got the loop coming around here for extra strength a little washer here if you wanted but I think it’s gonna be fine I just want to make sure I get one or two threads showing on that bolt and then I’m good to go.
So I’ve made sure this is all nice and flush on the front in the back on the front in the back and then I’ve.
Pre-drilled some holes again to avoid from the wood splitting and now I’m just going to put some 4-inch.
The next day and I’m not real happy with this joints it moves around in place too much because the 2×4 isn’t holding it in place so I’m upgrading to a 2 by 8 and we’re gonna put that sucker in there we’re gonna have to cut it down this way a little bit and because the design of this is to fold down and take apart this comes off this is bolted on to this piece I’ve got some screws I have to take out but that’s not a big deal and then this comes off so I can easily reconfigure this for the bigger piece without starting from scratch I’ve got this in the ideal configuration and I wanted to capture this angle instead of doing all the geometry so I’ve put a sheet of paper in there it happens to be perpendicular and then I just use my fingernail came down here and traced a line and that will get me really close to this angle so that when I cut it out this is a 2×4 so I know that distance add this on there and that will cut out and I’ll be able to get pretty close to the size I need when I go to cut this crosscut down here to put the 2 by 8 in place here’s just to show you that these cross pieces do come off.
It’s just design that easy and I put a b and b here so i could make sure that I line up the right side with the right side I’m using this old piece as the template to drill the hole it’s a lot easier than trying to drill the hole again and then I’m gonna come down on the angle with that paper that I had before I know all these holes are here I’m probably just going to tap those in and because this is a little drier piece of pressure-treated.
I’m gonna actually pre drill those holes on this piece so that they don’t split and taking the time to line this up and clamp it down right is really important because it saves you a lot of time and frustration to transcribe the angle I got off of the break over there.
I just lined this up and I put it up here as close as I can.
To get the approximation and as that comes down off the side I just take a center punch and marked it so that gives me the point to draw the line.
Pre-drilled all the holes here you can see that there’s more holes because they’re going through the wood and that actually marked it like it did last time so I can easily line it up I’m gonna make the second piece for the other end so all I’ve done is I’ve taken this piece that I’ve already cut I’ve marked the angle I’ve marked the side and the hole and drill that before I cut it off because it’s just easier to manage the piece here it is all back together again much stronger this guy is not rocking at all here it is on the other side.
Register lines really helped me put it back together this here is an eyelets a six-inch goes all the way through and it’s got a T nut this is the point you take apart when you want to flatten it down and it’s easy to do that you can use a screwdriver or a piece of dowel turn it around again yet it locks right in place nice and snug if I was to buy them over again I’d probably go with the eight-inch and have a little bit of extension kind of like I have here but then you just cut it off of you.
That’s annoying you but this one works solid the threads are right up there against the edge of the tee now just repeat everything I did on this side over here and then you’re done for my next version of this hammock frame I’m going to turn it into a skateboard look for that soon or if it’s already.
Available you’ll see it somewhere up here thumbs up and comments always appreciate thanks for watching and if you’re interested in these kind of things please subscribe I make and break all sorts of things.
I have outdoor projects indoor projects home repairs cosplay you just never know what you’re gonna see on my channel I post at least once a week and if I have extra time twice or more.
What is the standard weight capacity of your hammock stand?
Although the portable hammock stand is available in different magnitudes of size, weight capacity but the standard weight of your product must be around 450 lbs and the width should not be more than 6’ or else it will become spacious and will take enough of the space in your home. Still, there is some stand that is available in the market with more than this capacity but it the standard magnitude that you may consider to buy. But the most important thing is that it must be able to bear the weight of at least two people without letting you fall on the ground.
How to maintain the wooden or metal made hammock stand?
If you are worried about the resisting nature of your product against rust and other elements such as weather, then you can apply the oil on it which will protect it from the harsh wind of the winter. You can also cover it during the rainy season or wintertime or you can simply put it inside your home when you are not using it and this will keep it safe. More important is to make it resistant to rust so you must make it fewer expos to air and water. You can also go for the instruction manual to follow the important points on how to take care of your hammock stand.
What precautions should you take while using your hammock stand?
If you care about the long life of your hammock stand, then you need to follow some rules so that you could take care of it and use it for years. You should not put on weight on it more than its capacity or else it will be collapsed on the ground. You should not make your children jump or spin on your hammock or else it full be proved dangerous for them and also should not allow them to use it in absence of you or any adult.
Can your hammock stand damage the trees?
The amazing feature of the trees is that they do not get damaged when you put heavy objects on them or even screw the nails on them and it is a fact that they cover themselves wherever there is a stab or in other words, they are capable of healing themselves wherever they have wounds, so the hammock stand does not damage your trees. To avoid the girdling on the trees, you must make sure that you remove the straps if they are a part of invasive trees, or else it will affect their proper growth.
The hammock stand allows your hammock to hang up at an adjustable height according to your preference and they are easy to assemble. It offers you the rest and makes your comfortable while you release stress while lying on it as it keeps releases your back pain and you can lie on it while reading a book or simply taking a sunbathe. We highly hope that this review might have assisted you in knowing about the best portable hammock stand and what is the specification that you must consider before choosing the perfect one for yourself and your family.
Edmond Clark is a 34-year-old Blogger from California, USA. He is a Certified Market Research Professional (MRP) & a full-time blogger. His aim is to help the consumer to choose the best product from the market. Contact him for any of your queries.